你现在的位置:首页>企业动态>

打胶机胶阀滴漏及出胶大小不一致的原因

浏览:
打胶机在使用过程中会因为这样那样的因素而导致出现不少的问题,比如打胶机胶阀滴漏及出胶大小不一致的问题,下面济南双组份打胶机厂家为您讲解。
During the use of the sealant dispenser, many problems will occur due to such factors as leakage of the sealant valve and inconsistent size of the sealant. Now, the manufacturer of the two-component sealant dispenser in Jinan will explain to you.
胶阀滴漏。
The rubber valve leaks.
此种情形经常发生予胶阀关毕以后,95%的此种情形是因为使用的针头口径太小所致。太小的针头会影响液体的流动造成背压,结果导致胶阀关毕后不久形成滴漏的现象。
This often happens after the glue valve is closed, 95% of which is caused by the small diameter of the needle used. Too small a needle will affect the flow of liquid and cause back pressure, which will result in leakage soon after the rubber valve is closed.
过小的针头也会影响胶阀开始使用时的排气泡动作,只要更换较大的针头即可解决这种问题。液体内空气在胶阀关毕后会产生滴漏现象,预先排除液体内空气,或改用不容易含气泡的胶.或先将胶离心脱泡后在使用。
The too small needle will also affect the action of the exhaust bubble when the rubber valve starts to use. As long as the larger needle is replaced, this problem can be solved. The air in the liquid will drip after the rubber valve is closed. Remove the air in the liquid in advance, or use the glue that is not easy to contain bubbles, or centrifugate the glue before use.
济南双组份打胶机
出胶大小不一致。
The glue size is inconsistent.
当出胶不一致时主要为储存流体的压力筒或空气压力不稳定所产生。进气压力调压表应设定于比厂内低压力低10至15psi.压力筒使用的压力应介于调压表中间以上的压力,应避免使用压力介于压力表之中低压力部分。
When the glue outlet is inconsistent, it is mainly caused by the unstable pressure cylinder or air pressure of the fluid storage. The air inlet pressure regulating gauge shall be set at 10 to 15 psi lower than the low pressure in the plant The pressure of the pressure cylinder shall be above the middle of the pressure regulating gauge, and the pressure in the low pressure part of the pressure gauge shall be avoided.
胶阀控制压力应至少60psi以上以确保出胶稳定。后应检查出胶时间.若小于15/1000秒会造成出胶不稳定,出胶时间愈长出胶愈稳定。
The control pressure of glue valve shall be at least 60psi to ensure stable glue discharge. Then check the glue out time. If it is less than 15/1000 seconds, the glue out will be unstable. The longer the glue out time is, the more stable the glue out will be.
打胶机胶阀滴漏及出胶大小不一致的原因就讲解到这里了,您对此有什么想咨询了解的问题随时来我们网站http://www.jntiannuo.com看看吧!
This is the reason why the glue valve of the glue dispenser leaks and the size of glue is inconsistent. If you have any questions about this, please come to our website at any time http://www.jntiannuo.com Look!

上一篇:双组份打胶机的日常使用注意事项
下一篇:打胶机设计到制作再到出售整个的相关步骤

  • 官方微信